CommScope Ruckus ICX 7750 Hardware Installation Manual Download Page 77

Page: 77 / 91

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Ruckus ICX 7750 Specifications

Power supply specifications (per PSU)

Power supply specifications (per PSU)

Power consumption (typical configuration)

All ports linked and up. 50% traffic with 64-byte packets. Fans at normal speed.

Airflow

ICX 7750-26Q:

Back-to-Front: Maximum. - 55 cfm, Typical - 25 cfm

Front-to-Back: Maximum. - 62 cfm, Typical - 29 cfm

ICX 7750-48F:

Back-to-Front: Maximum. - 55 cfm, Typical - 25 cfm

Front-to-Back: Maximum. - 61 cfm, Typical - 29 cfm

ICX 7750-48C:

Back-to-Front: Maximum. - 55 cfm, Typical - 32 cfm

Front-to-Back: Maximum. - 62 cfm, Typical - 36 cfm

N/A

Heat dissipation

Refere to the power consumption tables.

N/A

Power
supply
model

Maximum
output power
rating (DC)

Input voltage

Input line frequency

Maximum
input
current

Input line
protection

Maximum inrush current

RPS9

504 W

100-240 VAC (nominal)
100-264 VAC (range)

50/60 Hz (nominal)

47 – 63 Hz (range)

7 A

Line fused

30 A peak cold or warm start for <10
ms

10 A peak for cycles 10 ms – 150 ms

Less than fuse rating for >150 ms

RPS9DC

504 W

-48 VDC (nominal)

-40 to -60 VDC (range)

15 A

-Ve fused

25 A peak cold or warm start for <10 ms

Less than 15 A after 150 ms

Model name

@100 VAC input

@200 VAC input

@-48 VDC input

Minimum number of
power supplies

Notes

ICX 7750-26Q

277 W

945 BTU/hr

274 W

935 BTU/hr

274 W

935 BTU/hr

1 AC or DC

Fan speed is at nominal.

ICX 7750-48F

254 W

867 BTU/hr

250 W

853 BTU/hr

250 W

853 BTU/h

1 AC or DC

Fan speed is at nominal.

ICX 7750-48C

510 W

1740 BTU/hr

511 W

1744 BTU/hr

511 W

1744 BTU/hr

1 AC or DC

Fan speed is at nominal.

Condition

Operational

Non-operational

Summary of Contents for Ruckus ICX 7750



























































































Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands

CommScope Ruckus ICX 7750, Hardware Installation Manual

Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands