manualshive.com logo in svg

CommScope Ruckus ICX 7750, Hardware Installation Manual

Share
Download
CommScope Ruckus ICX 7750 Hardware Installation Manual Download Page 68

66

Ruckus ICX 7750 Switch Hardware Installation Guide 

Part Number: 53-1003900-10

Managing the Ruckus ICX 7750

Replacing an expansion module

 

1.

If replacing a fan tray:

a.

Using a Phillips screwdriver, unscrew the captive screw on the fan tray.

b.

Remove the fan tray from the chassis by pulling the handle on the fan tray out and away from the chassis.

c.

Ensure that the replacement fan tray has the same part number and airflow label as the fan tray being replaced.

2.

If installing a new fan tray into a slot covered with a filler panel:

a.

Using a Phillips screwdriver, unscrew the captive screw on the filler panel.

b.

Remove the filler panel.

3.

Before opening the package that contains the new fan tray, touch the bag to the switch casing to discharge any potential static 
electricity. It is recommended that you wear an ESD wrist strap during installation.

4.

Remove the fan tray from the anti-static shielded bag.

NOTE

Do not force the installation. If the fan tray does not slide in easily, ensure that it is correctly oriented before continuing.

5.

Holding the fan tray level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it 
firmly engages with the connector.

6.

When you are sure the fan tray has properly engaged the connector, tighten the captive screw to secure the fan tray in the slot.

NOTE

The fans are controlled automatically by the device.

7.

Verify correct installation by running the 

show chassis

 command.

Replacing an expansion module

The Ruckus ICX 7750 includes a rear-panel slot for a 6-port QSFP+ 40 GbE expansion module. If not installed, the empty expansion 
module slot must be covered using the filler panel.

Time and items required

Replacing an expansion module in the Ruckus ICX 7750 should take less than two minutes to complete.

You need the following items to replace an expansion module in the Ruckus ICX 7750:

•

A new expansion module

•

A #1 Phillips screwdriver

CAUTION

If you do not install a power supply in a slot, you must keep the slot panel in place. If you run the device with an uncovered slot, 
the system will overheat.

CAUTION

Disassembling any part of the expansion module voids the warranty and regulatory certifications. There are no 
user-serviceable parts inside the expansion module assembly.

Summary of Contents for Ruckus ICX 7750




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands