CommScope Ruckus ICX 7750 Hardware Installation Manual Download Page 34

Page: 34 / 91

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295)

FIGURE 20

Attaching the rear brackets to the rack posts

Flush-rear (recessed) mounting the device in the rack

The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are reversed on the device.

NOTE

The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 1.5U or 2U device.
The illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a four-post rack:

“Attaching the front brackets to the rear of the device”

on page 33

“Attaching the extensions to the front of the device”

on page 33

“Installing the device in the rack”

on page 34

“Attaching the rear brackets to the extensions at the front of the device”

on page 35

“Attaching the rear brackets to the front rack posts”

on page 36

Screws, 10-32 x 5/8-in., panhead Phillips

Retainer nuts, 10-32

CAUTION

The device must be turned off and disconnected from the fabric during this procedure.

Summary of Contents for Ruckus ICX 7750



























































































Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands

CommScope Ruckus ICX 7750, Hardware Installation Manual

Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands