CommScope Mini-OTE 300 Tap Installation Instructions Manual Download Page 7 | Manualshive

Page: 7 / 10

CommScope Mini-OTE 300 Tap Installation Instructions Manual Download Page 7

TC-96203-IP
Installation Instructions

www.commscope.com

Page 7 of 10

Figure 8. Angled Connector End-Face Detail

3.

Locate the cleaning tape cassette that is provided with the cleaning kit.

4.

Open the tape shutter by squeezing the lever on the underside of the cassette and then keep the
shutter open by continuing to squeeze the lever.

5.

Hold the end-face of the drop cable connector perpendicular to the cleaning tape and with the
high side of the connector pointing in the direction of cleaning as shown in

6.

With light pressure, slide the connector end-face once across the tape in the direction shown
using a smooth linear motion. Do not press too hard and do not repeat the cleaning motion with
the same tape.

Note:

The drop cable connector uses angled SC type connectors. Make sure the high side of the
connector end-face is pointing in the direction of the cleaning motion

.

23591-A

CASSETTE

CLEANING

TAPE

DIRECTION

OF CONNECTOR

MOTION

ANGLED CONNECTOR

DETAIL DRAWING

PROTRUSIONS

PROTRUSIONS

«
...
5
6
7
8
9
...
»

Summary of Contents for Mini-OTE 300 Tap











Reviews:

No comments