CommScope F-042-GL-E Instruction Sheet Download Page 7 | Manualshive

Page: 7 / 8

CommScope F-042-GL-E Instruction Sheet Download Page 7

www.commscope.com

© 2019 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or

™ are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 7 of 8

A997-0086

1. Use a tether to secure the antenna’s hoisting eye to the mounting structure.

The tether can be a rope, wire rope, chain, or similar material. The tether should
be short enough to prevent the antenna from tilting beyond its maximum downtilt
range. This will prevent the antenna from tilting away from the mounting structure
when the adjusting bolts are removed.

Installed cables or the antenna may be damaged if they are allowed to strike the
mounting structure when the antenna mechanical downtilt is changed.

Figure 15: Upper Mounting Bracket Assembly

2.Loosen the fasteners holding the bottom antenna bracket to the bottom pivot
bracket. Do not remove them.

Figure 16: Lower Mounting Bracket Assembly

ADJUSTING MECHANICAL DOWN TILT AFTER INSTALLATION

F-042-GL-E, T-045-GL-E & T-041-GL-E

Loosen the
Fasteners

«
...
5
6
7
8
»

Summary of Contents for F-042-GL-E









Reviews:

No comments