manualshive.com logo in svg

CommScope e-POI, Installation Manual

Share
Download
CommScope e-POI Installation Manual Download Page 62

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

M0201ABK_uc 

Page 62

© June 2021 CommScope, Inc.

 Install and Connect the Subrack Cards

 

SFP+ Modules Tested for use with ERA

The following SFP+ modules are available from CommScope. These SFP+ modules have been tested by 

CommScope to ensure that they meet the requirements of an ERA system. This list was current at the time 

that this manual was published but is subject to change.

Install SFP+ Modules in the OPT Cards

The following steps tell you how to install the appropriate 10 Gbps SFP+ Module into the ports on the OPT 

Card that will be used to provide a 10 Gbps fiber connection between a CAN and a TEN or a WIN, or between 

a CAN or TEN and a Fiber AP. 

1

The SPF+ Module used must match the type of fiber used—Multi-Mode Fiber or Single-Mode Fiber (SMF 

or MMF). If necessary, contact your local CommScope sales representative to obtain the required number 

of SFP+ Modules for this installation. 
CommScope recommends testing with a device capable of certifying the end-to-end link (including the 

SFP+ Module) to ensure the installation meets the applicable 10Gbps Ethernet standard.

2

If the optical fiber path loss is below the minimum amount needed to prevent overdrive of the receiver, 

then insert an in-line optical attenuator to increase the loss above the minimum threshold.

Table 14. 

SFP+ Modules Tested for Use with ERA 

CommScope

Part No.

Description

Minimum 

Path Loss

CommScope

Part No.

Description

Minimum 

Path Loss

7660511

SFP+, 10GBase-SR, (MM)

0 dBm

7803295

IC SFP+ APSPC35B33CDL40 

Transceiver

5 dBm

7680813

SPF+, LR (SM)

0 dBm

7803298

IC SFP+ APSPC37B33CDL40 

Transceiver

5 dBm

7801330

SFP+ CWDM 1471 nm, 

10G-BASE-ER/EW, 10GbE

5 dBm

7803900

IC SFP+ APSPC39B33CDL40 

Transceiver

5 dBm

7801340

SFP+ CWDM 1491 nm, 

10G-BASE-ER/EW, 10GbE

5 dBm

7803902

IC SFP+ APSPC41B33CDL40 

Transceiver

5 dBm

7801342

SFP+ CWDM 1511 nm, 

10G-BASE-ER/EW, 10GbE

5 dBm

7803904

IC SFP+ APSPC43B33CDL40 

Transceiver

5 dBm

7801344

SFP+ CWDM 1531 nm, 

10G-BASE-ER/EW, 10GbE

5 dBm

7803906

IC SFP+ APSPC45B33CDL40 

Transceiver

5 dBm

7801360

SFP+ CWDM 1551 nm, 

10G-BASE-ER/EW, 10GbE 

5 dBm

7832204

10G BIDI SFP+ TX1270/RX1330 

40km I-temp

5.5 dBm

7801363

SFP+ CWDM 1571 nm, 

10G-BASE-ER/EW, 10GbE

5 dBm

7832206

10G BIDI SFP+ TX1330/RX1270 

40km I-temp

5.5 dBm

7801365

SFP+ CWDM 1591 nm, 

10G-BASE-ER/EW, 10GbE

5 dBm

7843514

SFP+, LC, 1310nm, max. 40Km

5.5 dBm

7801367

SFP+ CWDM 1611 nm, 

10G-BASE-ER/EW, 10GbE

5 dBm

7845626

10G BIDI SFP+ TX1310/RX1270 

20km I-temp 

2.5 dBm

7803247

IC SFP+ APSPC27B33CDL40 

Transceiver

5 dBm

7845627

10G BIDI SFP+ TX1270/RX1310 

20km I-temp 

2.5 dBm

7803249

IC SFP+ APSPC29B33CDL40 

Transceiver

5 dBm

7845628

CSFP BIDI Transceiver Tx-1270 / 

Rx-1310 (20km) 

2.5 dBm

7803291

IC SFP+ APSPC31B33CDL40 

Transceiver

5 dBm

7845629

CSFP BIDI Transceiver Tx-1310 / 

Rx-1270 (20km) 

2.5 dBm

7803293

IC SFP+ APSPC33B33CDL40 

Transceiver

5 dBm

Summary of Contents for e-POI























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands