Commend GE 800 Product Manual Download Page 32

Page: 32 / 43

General information

GE 800

4.2/0617

Dynamic audio channel allocation

Maximum number of conversations

Intercom Server GE 800 internal

The Intercom Server GE 800 has 128 internal channels. One conversation requires:



4 channels for 16 kHz audio



4 channels for 7 kHz audio



4 channels for 3.5 kHz audio



2 channels for 7 / 16 kHz All Calls/radio conferences/music



1 channel for 3.5 kHz All Calls/radio conferences/music

The result is that 32 conversations with 3.5, 7 or 16 kHz simultaneously within one Intercom Server
GE 800 are possible.

Conversations via G8-NET connection

Conversations per G8-NET card to other Intercom Servers (LAN conversations via a G8-NET card re-
duce this number):



32 conversations at 7 / 16 kHz



32 conversations at 3.5 kHz



48 radio conferences at 3.5 kHz

G8-NET to G7-GEV

28 conversations between GE 800 and GE 700.

G8-CNET-E1

10 conversations (in each mode).

G8-CNET-W

Depending on configuration 2 to 12 conversations (in each mode).

NOTE: Maximum number of radio conferences

A maximum of 48 radio conferences can be configured.

NOTES: Maximum number of LAN conversations



For details regarding the number of max. LAN conversations (e.g. in reference to the PRO 800 soft-
ware in use, compression etc.) see manual

“

G8-LAN, G3-LAN

”.



For details regarding the number of max. WAN conversations see manual “

WAN Networking

”.



For details regarding G8-NET (e.g. bandwidth etc.),

see page 19

NOTE: Maximum number of conversations per E1 connection

For details regarding the number of max. conversations per E1 connection, see manual “

G8-CNET-

”.

NOTE: Maximum number of conversations per CNET-W connection

For details regarding the number of max. conversations per CNET-W connection, see manual “

G8-

CNET-W

”.

Summary of Contents for GE 800












































Search results

Summary of Contents for GE 800

Reviews:

Related manuals for GE 800

Brands by name

Popular brands

Commend GE 800, Product Manual

Search results

Summary of Contents for GE 800

Reviews:

Related manuals for GE 800

Brands by name

Popular brands