Comm-Tec UP-82TS User Manual Download Page 7

Page: 7 / 56

Seamless Switcher

Comm-tec Srl

www.comm-tec.it

⚫

Supports HDMI output, HDBaseT output audio control.

⚫

Controllable via RS232 local and pass-through, IR local and pass-through, TCP/IP, relay,
CEC and on OSD.

1.2 Package List

Matrix Switcher

⚫

1x UP-82TS 8x2 HDMI 2.0 Seamless Matrix Switcher

⚫

2x Mounting Ears with 6 Screws

⚫

4x Plastic Cushions

⚫

1x IR Remote

⚫

1x IR Receiver

⚫

3x 3-pin Terminal Blocks

⚫

7x 5-pin Terminal Blocks

⚫

1x Power Adaptor (24V DC 5A)

Extender Kit

⚫

1x TPUH610AT HDBaseT Transmitter

⚫

1x TPUH610AR HDBaseT Receiver

⚫

4x Mounting Ears with 8 Screws

⚫

8x Plastic Cushions

⚫

1x 3-pin Terminal Block

⚫

1x RS232 Cable (3-pin to DB9)

⚫

1x User Manual

Note: Please contact your distributor immediately if any damage or defect in the
components is found.

Summary of Contents for UP-82TS
























































Search results

Summary of Contents for UP-82TS

Reviews:

Related manuals for UP-82TS

Brands by name

Popular brands

Comm-Tec UP-82TS, User Manual

Search results

Summary of Contents for UP-82TS

Reviews:

Related manuals for UP-82TS

Brands by name

Popular brands