Comfee CMP10 Instruction Manual Download Page 9

7

INSTALL REVERSE OSMOSIS FAUCET

1. The RO faucet is included with your RO System. 

Locate and organize the RO installation parts, see 

Figure 9 for more details on assembly.

2. Referring to Figure 9, You will need to install the 

part in the order shown, Stainless Steel Washer; 

Thin Black Washer.

Slide both onto the base of the faucet screw rod. 

The thin rubber washer should be sandwiched in 

between the faucet top and stainless steel washer.

3. Remove the red protective cap from the end of 

the RO faucet screw rod.  

4. Now install the RO faucet through the mounting 

hole. 

5. Under the cabinet install the following compo-

nents in this order: Reference Figure 9: Thick 

Black Rubber Washer; Metal Serrated Washer; 

Nut. 

In the order shown above, slide onto the base of 

the RO faucet screw rod.

6. Hand tighten the nut to threaded rod of the RO 

faucet until the faucet cannot move freely. Check 

the RO faucet to make sure the stainless steel 

washer and thin black washer is centered under 

the faucet. Once aligned, tighten the nut with an 

adjustable wrench.

7. The RO Faucet Base Connector is included with 

your RO System. Install this connector to the base 

of the faucet. Push connector onto faucet base 

until the connector bottoms out, see Figure 9.

8. You will attach the “BLUE” PE tube to the base 

of the faucet quick connect connector. 

9. After you have inserted the blue PE tube into 

the connector, insert the blue PE Tube Lock Clips 

into the quick connector end. See Figure 10 for 

order of installation. 

Each filter is individually wrapped in a plastic protective coating, remove and safely 

discard the plastic before installing filter into filter housing. You will find 6-black rubber 

O-Rings in a sealed zip-lock back. These will be installed onto the filter housing, see 

Figure 11. 

Note: The RO filter will NOT be installed at this time. We will install the 

RO filter after the RO system is flushed with fresh water. Refer to First Time Use 

– Flushing the Filters for more information.

Figure 9

Figure 10 

STEP 4 – Install Filters

Stainless Steel Tube

Stainless Steel Washer

Thin Black Washer

Countertop

Thick Hard Plastic Washer

Metal Serrated Washer

Nut

Outlet metal pipe

Red Protective Cap

PE Tube Lock Clip

Faucet Base Connector

PE Tube Lock CLip

Summary of Contents for CMP10





















Reviews: