Specifications are subject to change without notice.
IE-SNC-N-Tx6xx-03
Transmitters and transducers Web Sensor Tx6xx
with power over Ethernet - PoE
PRODUCT DESCRIPTION
Transmitters and transducers Web Sensor Tx6xx with Ethernet connection are designed to measure temperature, relative humidity
and barometric pressure of air in non-aggressive environment. Devices can be powered from external power supply adapter or by using
power over Ethernet - PoE.
Relative humidity transmitters allows to determine other calculated humidity variables like dew point temperature, absolute humidity,
specific humidity, mixing ratio and specific enthalpy.
Measured and calculated values are displayed on a two-line LCD display or can be read and then processed via Ethernet interface. The
following formats of Ethernet communication are supported: www pages with user-design possibility, Modbus TCP protocol, SNMPv1
protocol, SOAP protocol and XML. The instrument may send also a warning message if the measured value exceeds adjusted limit. The
messages can be sent up to 3 e-mail addresses or to Syslog server and can be sent by SNMP Trap too. The alarm states are also
displayed on the websites.
The device setup can be made by the TSensor software (see
www.cometsystem.com
) or using the www interface.
type *
measured values
version
mounting
T0610
T
ambient air
wall
T3610
T + RH + CV
ambient air
wall
T3611
T + RH + CV
probe on a cable
wall
T4611
T
external probe Pt1000/3850 ppm
wall
T7610
T + RH + P + CV
ambient air
wall
T7611
T + RH + P + CV
probe on a cable
wall
T7613D
T + RH + P + CV
the steel stem of length 150 mm
radiation shield COMETEO
* models marked TxxxxZ are custom - specified devices
T…temperature, RH…relative humidity, P…barometric pressure, CV…computed values
INSTALLATION AND OPERATION
The mounting holes and connection terminals are accessible after unscrewing four screws in the corners of case and removing the lid.
Devices have to be mounted on a flat surface to prevent their deformation. Pay attention to the location of the device and probe. Incorrect
choice of working position could adversely affect accuracy and long-term stability of measured value.
For the probe connection (T4611) it is recommended to use shielded cable with a length up to 10 m (external diameter 4 to 6.5mm). The
cable shielding is connected to proper terminal device only (do not connect it to other circuitry and do not ground it). All cables should be
located as far as possible from potential interference sources.
Devices don´t require special maintenance. We recommend you periodic calibration for measurement accuracy validation.
DEVICE SETUP
For network device connection it is necessary to know new suitable IP address. The device can obtain this address automatically from a
DHCP server or you can use the static IP address, which you can get from your network administrator. Install the latest version of TSensor
software to your PC, connect the Ethernet cable and the power supply adapter. Then you run TSensor program, set the new IP address,
configure the device in accordance with your requirements and finally store the settings. The device setup can be made by the web
interface too (see manual for devices at
www.cometsystem.com
).
The default IP address of each device is set to 192.168.1.213.
ERROR STATES
Device continuously checks its state during operation and if an error appears, it is displayed relevant code: Err 1 – measured or calculated
value is over the upper limit, Err 2 – measured or calculated value is below the lower limit or pressure measurement error occurred, Err 0,
Err 3 a Err 4 – it is a serious error, please contact distributor of the device.
SAFETY INSTRUCTIONS
- Humidity and temperature sensors can not be operate and store without a filter cap.
- Temperature and humidity sensors have not to be exposed to direct contact with water and other liquids.
- It is not recommended to use the humidity transmitters for long time under condensation conditions.
- Take care when unscrewing the filter cap as the sensor element could be damaged.
- Use only the power adapter according to technical specifications and approved according to relevant standards.
- Don’t connect or disconnect devices while power supply voltage is on.
- Installation, electrical connection and commissioning should be performed by qualified personnel only.
- Devices contain electronic components, it needs to liquidate them according to currently valid conditions.
- To supplement the information provided in this data sheet, use the manuals and other documentations which are
available at
www.cometsystem.com
.