Specifications are subject to change without notice.
ie-snc-n-p8x52-03
Web Sensor P8552 with binary inputs
PoE Web Sensor P8652 with binary inputs
PRODUCT DESCRIPTION
Web Sensor P8552 and Web Sensor P8652
with Ethernet connection
are designed to measure temperature and relative humidity of the
air. The devices are equipped with two connectors for connection of the temperature and humidity external probes and three binary inputs
for two-states signals. The dry contact or two-state voltage signal can be connect to the binary input. The devices are powered from an
external power supply adapter. Web Sensor P8652 supports also Power over Ethernet (PoE).
Measured values
can be read and then processed using an Ethernet connection. The following formats of Ethernet communication are
supported: www pages with user-design possibility, Modbus TCP protocol, SNMPv1 protocol, SOAP protocol and XML. The instrument
may send also a warning message if the measured value exceeds adjusted limit. The messages can be sent up to 3 e-mail addresses or
to Syslog server and can be sent by SNMP Trap too. The alarm states are also displayed on the websites. The device setup can be made
by the
TSensor
) and using the www interface.
type *
measured value
design
mounting
PoE
P8552
temperature, humidity
2-chanel transducer for external probe using, three binary inputs
wall
no
P8652
temperature, humidity
2-chanel transducer for external probe using, three binary inputs
wall
yes
* models marked Pxxxx
Z
are custom - specified devices
INSTALLATION AND OPERATION
The devices are designed for wall mounting with two screws or bolts. Pay attention to the location of the device and probe. Incorrect choice
of working position could adversely affect accuracy and long-term stability of measured values. The Web Sensor with attached DSRH/C
or DST/C probe install always vertically with the sensor cover downwards. Devices don´t require any special operation and maintenance.
We recommend you periodic calibration for measurement accuracy validation.
DEVICE SETUP
Contact your network administrator to obtain necessary information for the device connection into the network (IP address, default gateway,
subnet mask) and check if there is no IP address conflict when you connect the device into network for the first time. IP address of each
device is set by manufacturer to
192.168.1.213
. Install the latest version of TSensor to your PC, connect the Ethernet cable and connect
the power supply (see “Device connection procedure” on the other side of this data sheet).
Run the configuration software
TSensor
. Set the „
Ethernet“
communication interface and press „
Find Device
”
button. According to MAC
address (see device label) select device for configuration and by „
Change IP Address
”
button set new address according to network
administrator instructions. Gateway IP address may not be entered if you want to use the device only in local network.
After changing of
IP address the device is restarted and new IP address is assigned. Restart of the device takes about 10 seconds.
The device setup can be made by the web interface. Main page will be shown when you insert device address
into address bar of your web browser. Access to device setup is possible via tile
Settings
(see user manual).
To restore the Web Sensor to the
factory default settings
use the button inside the device.
Turn of the power supply and press the button (see picture). Turn on the power supply and keep
the button pressed for 10 sec.
ERROR STATES AND TROUBLESHOOTING
Device continuously checks its state during operation and if an error appears, the device sends the error message. The detailed description
of the error messages is given in the user manual Chapter “Troubleshooting”.
SAFETY INSTRUCTIONS
- Don’t use and don’t store the external relative humidity probe without a sensor cover.
- It is not recommended to use the external relative humidity probe for long time under condensation conditions.
- Don’t connect or disconnect thermometers while power supply is on.
- Installation, electrical connection and commissioning should be performed by qualified personnel only.
- Use the power adapter according to technical specifications and approved according to relevant standards only.
- The external probe cable should be located as far as possible from potential interference sources.
- If it is necessary connect the device to the Internet, properly configured firewall must be used.
-
The device should not be used for applications, where malfunction could cause to injury or damage to property.
- Devices contain electronic components, it needs to liquidate them according to legal requirements.
-
To supplement the information
provided in this data sheet, use the manuals and other documentations which
