background image

 
 

 

 

 

IE-COM-D0221-05

 

 

 

 

Temperature 

T1 of channel 1 is displayed on the upper LCD line in °C, 

temperature T2 of channel 2 is displayed on the lower LCD line in °C. 
 
 
 
Press  DISPLAY  key  to  display  the  difference  of  temperature  between 
channels (T dif = T1 - T2) on the LCD lower line (marked by DIF). 
 
 
The difference is displayed only if both temperature probes are connected. 
LCD upper line still displays temperature T1 of channel 1 

 
 
 
 

 

Function HOLD (storing of actual measured values) and 
minimum a maximum memory  

Press  HOLD  key  in  the  default  mode  (displaying  of  actual  measured 
temperature)  to  store  actual  measured  value  to  internal  memory 
(indicated  by  short  beep).  Anytime  it  is  possible to  display  stored  value 
from MENU (see below).  Each pressing of the HOLD key in the default 
mode  causes  value  stored  in  HOLD  memory  is  replaced  with  actual 
temperature.  

 

Switched  ON  instrument  permanently  updates  minimum  and  maximum 
memory  of  temperature.  Press  MIN  key  (resp.  MAX  key)  in  the  default 
mode to display minimum (resp. maximum) reading. These minimum and 
maximum  readings  are  indicated  by  MIN  (MAX)  symbols  on  the  LCD. 
Pressing  MIN  (MAX)  or  MENU  key  again  to  return  to  default  mode. 
Minimum and maximum memory is cleared from menu after confirmation 
selection  CLR  (see  below).  Values  in  HOLD,  MIN  and  MAX  memories 
remain stored even after instrument is switched OFF. 

 

 
 

 

 

Functions and settings available from menu  

 

Press MENU key to enter mode of viewing menu items one by one. Press 
arrow keys up and down to list all menu items. Press MENU key again to 
return to default mode (displaying of actual measured values). 

 

 

Summary of Contents for Commeter D0221





















Reviews: