ComAp InteliNano NT Plus Reference Manual Download

Page: 70 / 90

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

E10 Minimal Stabilization Time

Units:

seconds [s]

Step:

1 s

Range:

– 300 s

Default value:

3 s

Delay:

Minimum time after reaching of defined level of RPM to the closing GCB.

Prestart Time

> 8 s

Maximum

Cranking Time

0 - 60 s

Gen-set start failed – shutdown,

if the voltage or frequency are not in

the limit

Off

Time

Start

Engine run

Max. Stab. Time 7 s

Min. Stab. Time

Gen-set can be
loaded

Starter Output

Gen-set can be loaded
only when all running
condition are satisfied

E11 Starting RPM

Units:

Step:

Range:

– 60

Default value:

When Starting RPM are reached controller stops cranking. (Starter is disengaged.)

Summary of Contents for InteliNano NT Plus



























































































Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands

ComAp InteliNano NT Plus, Reference Manual

Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands