ComAp InteliLite MRS16 Manual Download Page 85

Page: 85 / 632

InteliLite Global Guide

Breaker open and cool down (BOC)

The event appears in the alarmlist and is recorded into the history log. It causes immediate opening of the GCB

and then the standard stop sequence with cooling follows. The gen-set cannot be started again while there is a

BOC alarm in the alarmlist. Activates the output

as well as the standard alarm

outputs (

and

Sensor fail detection (FLS)

If the measured resistance on an analog input exceeds the valid range, a sensor fail will be detected and a

sensor fail message will appear in the

Alarmlist (page 86)

. The valid range is defined by the most-left (RL) and

most-right (RH) points of the sensor characteristic ±12.5% from RH-RL.

Note:

Sometimes there can be problem with lower limit of valid range which can be counted as negative

number. In this case the lower limit is set as one half of the RL point of the sensor curve characteristic.

Image 5.17 Sensor fail detection principle

Remote alarm messaging

If communication plug-in module is connected to the controller, the controller can send SMS messages and

emails at the moment when a new alarm appears in the

Alarmlist (page 86)

or new event is written in

History

log (page 88)

. The message will contain a copy of the

Alarmlist (page 86)

or reasons from

History log (page

88)

To enable this function, you should select adjust setpoints

Event Message (page 329)

Wrn Message (page 329)

BOC Message (page 329)

and

Sd Messages (page 330)

to select the types of messages. Also enter a valid GSM

phone number or email address to the setpoints

Telephone Number 1 (page 322)

Telephone Number 2 (page

323)

Telephone Number 3 (page 323)

Telephone Number 4 (page 324)

Email Address 1 (page 326) Email

Address 2 (page 326)Email Address 3 (page 327)

, and

Email Address 4 (page 327)

The list of all supported terminals shows the table below:

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands