ComAp InteliLite MRS16 Manual Download Page 593

Page: 593 / 632

InteliLite Global Guide

593

Related applications

AMF, MRS

Description

This is a fast overcurrent protection. The following setpoints are related to this

alarm:

Short Circuit BOC (page 195)

adjusts the short current limit

Short Circuit BOC Delay (page 195)

adjusts the delay in fine steps

back to List of alarms level 2

Alarm Type

Shutdown

Alarmlist message

Sd Start Fail

Alarm evaluated

When the gen-set is being started

Related applications

AMF, MRS

Description

This alarm will be issued after all attempts to start the gen-set have run out but the

gen-set did not start. The following setpoints are related to this alarm:

Cranking Attempts (page 165)

adjust the number of attempts

Sd Start Fail

back to List of alarms level 2

Alarm Type

Shutdown

Alarmlist message

Sd Underspeed

Alarm evaluated

Engine running only

Related applications

AMF, MRS

Description

This alarm will be issued when the gen-set is running and then stops by itself, i.e.

the RPM drops under the value of setpoint

Starting RPM (page 166)

The underspeed alarm starts to be evaluated after successful gen-set start and is

being evaluated for the entire time that the fuel solenoid is on.

Sd Underspeed

back to List of alarms level 2

Other type

Alarm Type

BOC

Alarmlist message

BOC Coolant Temperature

Alarm evaluated

All the time

Related applications

AMF, MRS

Description

This alarm indicates that the coolant temperature is higher than the temperature set

Coolant Temperature Sd (page 179)

setpoint.

BOC Coolant Temp

back to List of alarms level 2

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands