ComAp InteliLite MRS16 Manual Download Page 553

Page: 553 / 632

InteliLite Global Guide

553

Image 9.4 Configuration of Comp Hyst block

Note:

Level On and Level Off can be constants or values from controller.

IMPORTANT: In case that values on inputs have different decimal numbers than the values

are converted and the name of block is red. It is strongly recommended to use values with

the same decimal numbers.

back to List of PLC blocks

PLC group

Comparison of analog

inputs

Related FW

1.2.1

Related applications

AMF, MRS

Comm object

Inputs

Input

Type

Negation

Range

Function

Input 1

Analog

Any

Compared value

Input 2

Analog

Same as Input 1

Comparative level

Delay

Analog

0.0..3000,0 [s]

Comparative delay

Outputs

Output

Type

Negation

Range

Function

Output

Binary

0/1

Comparator output

Description

The block works as an analog switch. It compares the input value with the comparative level. The output will

switch on if the input is equal or higher than the comparative level for time longer than the delay.

Comparator With Delay

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Brands by name

Popular brands