ComAp InteliLite MRS16 Manual Download Page 503

Page: 503 / 632

InteliLite Global Guide

503

LBO: I

Related FW

1.2.1

Related applications

AMF, MRS

Comm object

Description

This output is used for switching between idle speed and nominal speed of the engine during the startup

phase, if this feature (input) is available on the particular engine. In the case of some EFI engines, the

idle/nominal switching is performed over the communication bus.

The output Idle/Nominal closes after the timer

Idle Time (page 169)

elapses. The

Idle Time (page 169)

starts

to countdown when

Starting RPM (page 166)

reached. The underspeed protection is not evaluated during

fixed 5 seconds period after reaching

Starting RPM (page 166)

. A Start Fail protection occurs if the RPM drop

below 2RPM during idle.

Image 8.176 Idle/Nominal

Note:

Connect binary output Idle/Nominal to speed governor to switch the speed:

opened = Idle

closed = Nominal

(for normally open contact type)

Idle/Nominal

back to Logical binary outputs alphabetically

Related FW

1.2.1

Related applications

AMF, MRS

Comm object

Description

This output is dedicated to controlling the ignition at a gas engine. The output is closed together with binary

output

in the moment when the timer

Sd Ventilation Time (page 173)

elapsed and

the gen-set reaches at least 30 RPM during cranking. The timer

Sd Ventilation Time (page 173)

become

active when the gen-set has been stopped for any Sd protection or the controller has been turned on only

before first cranking attempt. The output is opened 500ms after all Additional running engine indication

Additional running engine indications (page 103)

will be inactive. The output is opened when the gen-

set has to be stopped or in pause during repeated starts.

Ignition

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Brands by name

Popular brands