ComAp InteliLite MRS16 Manual Download Page 404

Page: 404 / 632

InteliLite Global Guide

404

8.1.2 Values

What values are:

Values (or quantities) are analog or binary data objects, measured or computed by the controller, that are

intended for reading from the controller screen, PC, MODBUS, etc. Values are organized into groups according

to their meaning.

Invalid flag

If valid data is not available for a particular value, the invalid flag is set to it. This situation may be due to the

following:

The value is not being evaluated in the scope of the current application and configuration.

Sensor fail has been detected on an analog input.

The configured ECU or extension module does not provide the particular value.

The communication with the ECU or extension module is interrupted.

A value containing the invalid flag is displayed as “####” in LiteEdit2015 and on the controller screen. If such a

value is read out via MODBUS, it will contain the data 32768 in the case of signed values and 65535 in the case

of unsigned values.

List of values groups

For full list of setpoints go to the chapter

List of values (page 405)

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands