ComAp InteliLite MRS16 Manual Download Page 161

Page: 161 / 632

InteliLite Global Guide

161

Subgroup: Controller settings

Setpoint group

Basic settings

Related FW

1.2.1

Range [units]

OFF / MAN / AUTO / TEST [-]

Default value

OFF

Alternative config

Step

[-]

Comm object

8315

Related applications

AMF, MRS

Config level

Advanced

Setpoint visibility

Always

Description

This setpoint can be used for changing the Controller mode remotely, e.g. via MODBUS. Use the mode

selector on the main screen for changing the mode from the front panel. Use mode selector in the control

window for changing the mode from LiteEdit2015.

Controller mode

back to List of setpoints

Setpoint group

Basic settings

Related FW

1.2.1

Range [units]

1 .. 32 [-]

Default value

Alternative config

Step

Comm object

24537

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Always

Description

Controller identification number. It is possible to set controller address different from the default value (1) so

that more IL controllers can be interconnected (via RS485) and accessed e.g. from MODBUS terminal.

Note:

When opening connection to the controller it's address has to correspond with the setting in PC

tool.

Note:

This setpoint is common for CM-Ethernet, CM-GPRS and CM-4G-GPS modules.

Controller Address

back to List of setpoints

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands