manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

42

Extension modules addressing

All I/O function or protection configuration

Setpoints adjusting

Sensor characteristics modification

History record modification

Password level protection modification (password value must be changed in DriveMonitor)

Controller firmware (mhx file) upgrade

Controller application file Up/Down load

Language translator enables (not available in version 1.0)

Create Dictionary between two languages (Dictionary can be used repeatedly)

Translate current text in Controller (in any language)

Add new language (up to controller memory limit)

Internal PLC editor

5.1.3 Configuration steps

Note:

Before ID-Mobile ECU configuration switch to ECU list: Option – ESL files … select Mobile.esl

Following configuration steps are available in DriveConfig software:

Configure J1939 interface when Electronic engine is connected

Configure Binary inputs as Protection or Function

Configure Binary outputs

Configure Analog inputs as Protection or Function

Define user sensors (in Expert mode only).

Configure History record (in Expert mode only)

Configure password protection

Add/Translate the language (in Expert mode only)

Translator

Enables to translate all or some texts to up 5 languages that are all available in controller. Controller language

can be changed from panel buttons. It is possible to operate different languages on each ID-Mobile and Drive

Monitor. External display (e.g. Bodas and CANtrak) language depends on specific display firmware.

Note:

Check all screens after translation if some texts do not overflow.

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

Watts 800 Series Instructions For Installing preview
800 Series
Brand: Watts Pages: 2
Hardi HC5500 Quick Manual preview
HC5500
Brand: Hardi Pages: 2
YASKAWA CC-Link Technical Manual preview
CC-Link
Brand: YASKAWA Pages: 64
V2 Phoenix Programming Manual preview
Phoenix
Brand: V2 Pages: 3
GARAN EWS-102 Calibration & Setup preview
EWS-102
Brand: GARAN Pages: 8
Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
Mamas & Papas Tour Instructions Manual preview
Tour
Brand: Mamas & Papas Pages: 24
Mamas & Papas 03 Sport Owner'S Manual preview
03 Sport
Brand: Mamas & Papas Pages: 24
Saluki SMR Series Quick Start Manual preview
SMR Series
Brand: Saluki Pages: 13
XtendLan KEYBPTZ4D Operating Instructions Manual preview
KEYBPTZ4D
Brand: XtendLan Pages: 12
ZBA ZZB88-441S User Manual preview
ZZB88-441S
Brand: ZBA Pages: 27
M-system R7C-RS4 Instruction Manual preview
R7C-RS4
Brand: M-system Pages: 10
EMS ZITON RADIO LOOP MODULE Programming Manual preview
ZITON RADIO LOOP MODULE
Brand: EMS Pages: 26
Danfoss 084B8012 Instructions Manual preview
084B8012
Brand: Danfoss Pages: 30
Finnleo SaunaLogic SL2 Control Manual preview
SaunaLogic SL2 Control
Brand: Finnleo Pages: 14
SILENTRON SERENYA 2000 Manual preview
SERENYA 2000
Brand: SILENTRON Pages: 20
MacroAir Technologies Controller 30 Operation Manual preview
Controller 30
Brand: MacroAir Technologies Pages: 32

Brands by name

Popular brands

Load more brands