manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

173

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

74

Description

Closes in cooling state, opens after engine stop.

Cooling

6

back to List of LBO

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

260

Description

CPU indication – output is closed when CPU is ready, opened in Init state.

CPU Ready

6

back to List of LBO

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

81

Description

Indicates correctly running firmware when cycling on/off with 0.5 sec period.

CtrlHeartBeat

6

back to List of LBO

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

428

Description

ID-Mobile Logical Binary Output (LBO) “Display Key x” is activated when corresponding Bodas button is

pressed – see in table below. The first button does not activate the LBO Display Key 1.

LBO

Bodas button

No LBO function

1-st “round”

Display Key 2

2-nd

Display Key 3

3-rd

Display Key 4

4-th

Display Key 5

5-th

Display Key 6

6-th

Note:

Bodas keys procedures are not available in standard Bodas-1.3 firmware, it is dedicated for future

customer branches.

Display Key 1

6

back to List of LBO

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

zipwake S Series Troubleshooting Manual preview
S Series
Brand: zipwake Pages: 12
Watts 7 Series Installation, Maintenance & Repair preview
7 Series
Brand: Watts Pages: 2
jbc UCR Instruction Manual preview
UCR
Brand: jbc Pages: 12
UE 120 Series Installation And Maintenance Instructions preview
120 Series
Brand: UE Pages: 4
XBOX 360 Manual preview
360
Brand: XBOX Pages: 7
NEC NEAX 2400 ICS Manual preview
NEAX 2400 ICS
Brand: NEC Pages: 149
NEC LED-E012i User Manual preview
LED-E012i
Brand: NEC Pages: 13
babyzen YOYO User Manual preview
YOYO
Brand: babyzen Pages: 11
M-system SC100 Series Applications Manual preview
SC100 Series
Brand: M-system Pages: 103
M-system MSP40 Instruction Manual preview
MSP40
Brand: M-system Pages: 18
M-system 47LV Specifications preview
47LV
Brand: M-system Pages: 7
Packard Bell Slim Remote Control Instruction preview
Slim Remote Control
Brand: Packard Bell Pages: 2
Unipower PCM500 Series Operating Manual preview
PCM500 Series
Brand: Unipower Pages: 24
Ziton ZP1-X3E Series Operation Manual preview
ZP1-X3E Series
Brand: Ziton Pages: 36
Nice TT6 Instructions And Warnings For Installation And Use preview
TT6
Brand: Nice Pages: 120
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Brand: Bailey Pages: 75
mr. steam iSteam 2.0 Control Installation, Operation & Maintenance Manual preview
iSteam 2.0 Control
Brand: mr. steam Pages: 16
Sygonix 2446222 Operating Instructions Manual preview
2446222
Brand: Sygonix Pages: 12

Brands by name

Popular brands

Load more brands