manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

108

Setpoint group

Date/Time

Related FW

2.6.0

Range [units]

[DD:MM:YY]

Default value

##.##.##

Step

Comm object

24553

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Actual date adjustment.

Date

6

back to List of setpoints

Setpoint group

Date/Time

Related FW

2.6.0

Range [units]

0 .. 240 [min]

Default value

1

Step

1 min

Comm object

8979

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Time interval for history record. Time base is based on number of minutes since midnight.

Note:

No history Time stamp is recorded when TimeStamp Per = 0.

RTC and Date is in each History record.

Time stamp per

6

back to List of setpoints

Setpoint group

Date/Time

Related FW

2.6.0

Range [units]

[ALL TIME, RUNNING ONLY, BI HISTORY]

Default value

RUNNING ONLY

Step

Comm object

12162

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The history can be forced to list as follow:

ALL TIME

History records are active all time.

RUNNING ONLY History is recorded when engine is running only.

BI HISTORY

History record is forced when LBI BI History is configured and liked with binary input.

HistoryEntries

6

back to List of setpoints

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

T-Verter E2 Series Operating Manual preview
E2 Series
Brand: T-Verter Pages: 121
Happy 1050 Installation & Use Instructions preview
1050
Brand: Happy Pages: 10
Eaton SC100 Operation Handbook preview
SC100
Brand: Eaton Pages: 86
Abus HomeTec Pro CFF3000 Operation preview
HomeTec Pro CFF3000
Brand: Abus Pages: 13
NAVITAS 440A Installation & Service Manual preview
440A
Brand: NAVITAS Pages: 7
Abus PLHA10000 Quick Manual preview
PLHA10000
Brand: Abus Pages: 2
Febco Master Series Installation Instructions Manual preview
Master Series
Brand: Febco Pages: 12
GameSir G4s User Manual preview
G4s
Brand: GameSir Pages: 8
Game ready 550450 User Manual preview
550450
Brand: Game ready Pages: 21
VAMP 259 Operation And Configuration Instructions preview
259
Brand: VAMP Pages: 304
Tactical TTC Instruction Manual preview
TTC
Brand: Tactical Pages: 8
K1EL WinKeyer3 Operation Manual preview
WinKeyer3
Brand: K1EL Pages: 46
QUNDIS Q Module WFZ16.Ox Mounting And Installation Instructions Manual preview
Q Module WFZ16.Ox
Brand: QUNDIS Pages: 24
bihl+Wiedemann BW3489 Installation Instructions Manual preview
BW3489
Brand: bihl+Wiedemann Pages: 16
Trane Tracer CH.530 RLC-SVU01B-E4 Owner'S Manual preview
Tracer CH.530 RLC-SVU01B-E4
Brand: Trane Pages: 60
Monster Central REVOLUTION 200 Instruction Manual preview
REVOLUTION 200
Brand: Monster Central Pages: 13
Rain Bird ESP-RZXe Installation And Operation Manual preview
ESP-RZXe
Brand: Rain Bird Pages: 18
AT&T U-verse Advance Series A10 Product Manual preview
U-verse Advance Series A10
Brand: AT&T Pages: 2

Brands by name

Popular brands

Load more brands