manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 69 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 69

ID-FLX Lite Global Guide

69

Input

Analog input

CU: AI1-AI9

AIO: AI1-AI4

Binary output

Load Switch

Setpoints

Load limit

Load CMP Input = AI1

Load CMP On = 90

Load CMP Off = 80

Engine load limitation with On/Off output

Purpose: Protect the engine against overload by reducing (switching On/Off) the load.

Description: CMPH (Comparator with Hysteresis) detect the RPM decrease below the Down limit, activates

the Binary output Load switch that reduces (slow down feeder) the load. There are expected corresponding

droop characteristics on the engine.

Input

RPM from pickup (or ECU)

Binary output

Load Switch

Setpoints

Load limit

Load CMP Input = RPM

Load CMP On = e.g. 2000

Load CMP Off = e.g. 2200

Speed switch

Purpose: Switch on/off some device depends on RPM level.

Description: Depends on setpoint settings the CMPH (Comparator with Hysteresis) activates/deactivates the

Binary output Load switch that switch off some device when RPM is below adjusted limit.

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments