ComAp InteliDrive FLX LITE Manual Download Page 170

Page: 170 / 228

ID-FLX Lite Global Guide

170

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

No Func, AutoRun, AutoRegCMP, AutoBatt, AutoStop [-]

Default value

No Func

Step

Comm object

11661

Related applications

Description

No Func

Operates just corresponding

according the

setting, see

Timer2repeat (page 171)

Timer2 ON time (page 171)

Timer2Duration (page 171)

. Function operates in all OFF-MAN-AUT modes.

Default state.

AutoRun

Engine automatically starts and stops in AUT mode (similar to

, the same record in the history) according the

setting.

AutoRegCMP

Start and stop engine in AUT mode according to the

- see

Reg CMP Input (page 133)

. The comparator function (output) works opposite

when

Reg CMP On (page 133)

Reg CMP Off (page 134)

. The

Timer2repeat

(page 171)

Timer2 ON time (page 171)

Timer2Duration (page 171)

are not

important in this case.

AutoBatt

Engine starts when actual Battery voltage <

Batt undervolt (page 145)

Batt volt

del (page 145)

and stays running for

Timer2Duration (page 171)

. Function

operates in AUT mode.

AutoStop

Engine is switched from AUT to MAN and stopped or stopped from MAN mode (like

by STOP button) when engine runs longer then

Timer2Duration (page 171)

actual RPM less or equal

Idle speed (page 118)

+ 5% (fix limit). Function is not

active during engine start.

Timer2Function

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 170 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: