manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 167 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 167

ID-FLX Lite Global Guide

167

Group: Date/Time

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

0 .. 240 [min]

Default value

60

-

Step

1

Comm object

8979

Related applications

Description

This setpoint is dedicated to adjustment of time interval for periodical history records.

Time stamp per

6

back to List of setpoints

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

DISABLED, WINTER, SUMMER, WINTER-S, SUMMER-S [-]

Default value

-

Step

-

Comm object

8727

Related applications

Description

DISABLED

Automatic switching between summer and wintertime is disabled.

WINTER

(SUMMER)

Automatic switching between summer and winter time is enabled and it is set to

winter (summer) season.

WINTER-S

(SUMMER-S)

Modification for southern hemisphere.

SummerTimeMod

6

back to List of setpoints

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

[HH:MM:SS]

Default value

-

Step

-

Comm object

24554

Related applications

Description

Actual time.

Time

6

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments