manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 106 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 106

ID-FLX Lite Global Guide

106

Group: Communication settings

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

-

Step

-

Comm object

24537

Related applications

Description

It is controller’s identification number. It is possible to set controller address different from the default value 1

so that more ID-Lite controllers can be interconnected (via RS485) and accessed e.g. from Modbus terminal.

Adresses

1 .. 32

Note:

When opening connection to the controller its address has to correspond with the setting in PC

tool.

ControllerAddr

6

back to List of setpoints

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[DIRECT / MODEM / MODBUS / ECU LINK]

Default value

-

Step

-

Comm object

24522

Related applications

Description

Communication protocol switches for the COM1 channel.

DIRECT

LiteEdit communication protocol via direct cable or AirGate, WebSupervisor

communication protocol via AirGate.

MODEM

LiteEdit communication protocol via modem.

MODBUS

Modbus protocol. See detailed description in

InteliDrive Communication Guide

.

ECU link

Protocol for communication with Cummins engines via Modbus.

Note:

For details on communication speed and other technical parameters please

see Technical data

on page 90

.

For detail description see chapter Modbus protocol.

COM1 Mode

6

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments