manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 100 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 100

ID-FLX Lite Global Guide

100

Setpoint group

Basic settings

Related FW

2.5.0

Range [units]

50.00 .. 200.00 [-]

Default value

1

-

Step

0.01

Comm object

8420

Related applications

Description

The constant of this setpoint multiplies the speed value obtained from the controller input RPM.

Note:

The default value is and must be 1, when the classical pick-up speed sensor is used to measure

the engine speed.

The setpoint is usefull when the engine does not have the speed sensor and the speed is measured by

the W terminal of the charging alternator. The setpoint allows tuning the ratio between the frequency and

the RPM value which can not to correspond to the entire values of teeth numbers (because of the

different non-integral ratio of the engine and alternator pulleys).

RPMbyWterminal

6

back to List of setpoints

Setpoint group

Basic settings

Related FW

2.5.0

Range [units]

100 .. 4000 [RPM]

Default value

-

Step

1

Comm object

8253

Related applications

Description

Nominal engine speed, base for overspeed protection and scale on RPM gauges.

Nominal RPM

6

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments