ComAp InteliDrive DCU Marine Manual Download

Page: 30 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Engine running state

RPM > Engine params:

Starting RPM

Logical Analog Input

Oil Press

> Engine params:

Starting Poil

Logical Analog Input

Coolant Press

> Engine params:

StartPCoolant

(

PRP

only) or

active BI

RunIndication1

active BI

RunIndication2

active BI

RunIndication3

3.1.3 Operational modes

LOC (Local) mode

LOC

(Local) mode can be set in any mode mentioned above –

AUX, EME, HRB, PRP

. ID-DCU MARINE

receives only commands entered from the ID-DCU MARINE front panel in LOC (Local) mode. All external

interfaces – binary inputs

Remote Start, Blackout Start, RemRepStart, Remote Stop, Rem Start/Stop

and

serial line commands are disabled.

LOC

(Local) mode is activated and deactivated using ID-DCU MARINE front panel buttons: Enter + Mode→ to

activate, Enter + ←Mode to deactivate. Active

LOC

(Local) mode is indicated in the upper right corner of the ID-

DCU MARINE display.

OFF mode

All ID-DCU MARINE controller and ID-RPU binary outputs are switched off. Engine can’t be started or running

engine is stopped, prelubrication function is not active. Firmware and controller configuration can be changed in

OFF

mode only.

OFF

mode is available in all applications –

AUX, EME, CMB

and

PRP

Auxiliary mode (AUX archive)

AUX

mode is designed for auxiliary engines.

Controller starts and stops the engine according to the binary inputs

Blackout Start

Remote Start

Rem

Start/Stop

Remote Stop

or to the ID-DCU MARINE

Start / Stop

buttons. Binary inputs Blackout Start

and Remote Start and Remote Stop are inactive in

LOC

(Local) mode.

All engine protections and all configured shutdown protections are active. Controller continuously monitors

all available engine parameters (oil pressure, water temperature, RPM, fuel level etc.). The engine will stop

and activates

Common Warning

and

Common Shutdown

outputs and writes record to the history file

when detects any active Shut down alarm. This condition can be signaled by Active call feature to remote

operator via modem, SMS or e-mail.

Emergency mode (EME archive)

The engine is used for emergency engines.

Controller starts and stops the engine according to the binary inputs

Blackout Start

Remote Start

Rem

Start/Stop

, Remote Stop or to the ID-DCU MARINE

Start / Stop

buttons. Binary inputs

Blackout Start

and

Remote Start

and

Remote Stop

are inactive in LOC (Local) mode.

The controller still measures all engine parameters. But it only records to the history file and can notify

remote operator via Active call when detects any parameter out of range.

The only active shut down protection is engine overspeed and Emergency stop.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands