ComAp InteliDrive DCU Marine Manual Download

Page: 23 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Note:

The WebSupervisor ComAp tool is supported from ID-DCU Marine version 2.2, specifically fromID-

DCU-MARINE-W-2.2.mhx firmware.

2.3 List of supported modules

Product

Description

Order code

Inteli AIN8

8 Analog inputs (R, I, V) and 1 pulse/frequency input

I-AIN8

Inteli AIN8TC

8 Thermocouple Analog inputs

I-AIN8TC

Inteli IO8/8

8 Binary inputs, 8 Binary outputs and 2 Analog outputs packed in

a small unit (HW switchable to IO16/0). HW switchableto IO16/0

- 16 Binary inputs

I-IO8/8

IS-BIN 16/8

16 configurable galvanically separated inputs, 8 configurable

outputs

IS-BIN16/8

Inteli AIO9/1

9 Analog inputs (4x DC, 4x thermocouples, 1x R)

I-AIO9/1

IS-AIN8

8 Analog inputs packed in a rugged metal unit

IS-AIN8

IS-AIN8TC

8 analog inputs for thermocouple measurement, supports J, K, L

types

IS-AIN8TC

IGS-PTM

8 Binary inputs, 8 Binary outputs, 4 Analog inputs and 1 Analog

output

IGS-PTM

IB-NT

Internet bridge

IB-NT

I-CB

Communication bridge

I-CB

I-AOUT8

8 Analog outputs

I-AOUT8

You can get more information on wiring of standard extension modules in the chapter

Extension modules

(page 69)

back to System overview

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands