ComAp InteliDrive DCU Marine Manual Download

Page: 21 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Sensor characteristics modification

History record modification

Password level protection modification (password value must be changed in InteliMonitor)

Additional PLC logic creating

InteliVision displays screens modification

ECU Fault codes management

Controller firmware (mhx file) upgrade

Controller application file Up/Down load

Language translator enables (not available in version 1.0)

Create Dictionary between two languages (Dictionary can be used repeatedly)

Translate current text in Controller (in any language)

Add new language (up to controller memory limit)

PC to ID-DCU MARINE controller connection

Uploading or downloading procedure only (no continuous on-line connection)

Direct RS232 connection

Modem and internet connection

2.2.5 Modbus protocol

Direct connection: RS232, RS422, RS485

Modem connection

9600, 19200, 38400, 57600 or 115200 bps, 8 data bits, 1 stop bit, no parity

Transfer mode RTU

Function 3 (Read Multiply Registers)

Function 6 (Write Single Register)

Function 16 (Write Multiply Registers)

The response to an incoming message is sent with minimum 4.096 ms delay after message reception

The complete description of Modbus communication protocol can be found in Modbus Protocol Reference

Guide PI-MBUS-300 and Open Modbus Specification Release 1.0. Both documents are available from web site

http://www.modicon.com/openmbus/

Communication object vs. Register

All the data intended for communication has its representation as communication objects in the controller. The

communication object is represented by the n-byte array in the controller memory and identified by the unique

16-bit communication object number. The register, according to Modbus communication protocol, represents a

two-byte data and in communication functions is referenced by 16-bit register address. Further in the description

of communication functions the communication object number will always be used as a register address and

length of the communication object will be expressed by number of registers. Just one communication object

can be read or written by one communication function.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands