ComAp InteliDrive DCU Marine Manual Download

Page: 186 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

186

Related FW

3.0.0

Related applications

All

Comm object

Description

Skips Idle Time and switch controller from Idle to Running state when closed before Idle Time is over.

Nominal Speed

back to List of LBI

Related FW

3.0.0

Related applications

All

Comm object

162

Description

Binary input function for loaded engine indication.

Loaded

back to List of LBI

Related FW

3.0.0

Related applications

All

Comm object

Description

This input is designed to allow the engine to be controlled externally, not by the controller. This feature is

especially designed for marine gen-sets, which are supposed to be started manually as the controller has no

power supply before the gen-set is started. It may be also useful in case of testing the gen-set or in case of a

failure, which does not allow the gen-set to be controlled by the controller, but the gen-set itself is stays

operational.

The controller behaves following way:

Shows the text EmergMan in the engine status on the main screen.

Stops all functions regarding the engine control, deactivates all outputs related to it except Fuel

Solenoid.

Stop Fail alarm is not being evaluated and Stop Solenoid is not activated if nonzero speed is

detected.

When the input is deactivated, the controller takes control over the engine according to the situation

in which the gen-set was in the moment of deactivation. I.e. the engine remains running if it was

running in the moment the input was deactivated.

Emerg. Manual

back to List of LBI

Related FW

3.0.0

Related applications

PRP

Comm object

163

Description

Binary input activates Engine start via clutch. Engine is started by the other running engine via closed clutch

- binary output

Clutch Connect

. See

MaxClStrtPer (page 156)

protection setpoint.

EnClutchStart

back to List of LBI

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands