ComAp InteliDrive DCU Marine Manual Download

Page: 122 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

122

Setpoint group

Comms Settings

Related FW

3.0.0

Range [units]

[19200, 38400, 57600, 115200] [bps]

Default value

38400 bps

Step

[-]

Comm object

24340

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

The setpoint adjusts communication speed of the RS485 interface when

RS485 Mode (page 121)

is set to

STANDARD.

RS485 TermCSpd

back to List of setpoints

Setpoint group

Comms Settings

Related FW

3.0.0

Range [units]

[DISABLED, ENABLED]

Default value

ENABLED

Step

[-]

Comm object

11024

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

This setpoint is used to enable/disable evaluation of collisions of virtual shared peripherial modules. A

collision means that there is more than one source (shared outputs module) active on the CAN2 bus.

Note:

In certain situations multiple sites with bus tie breakers may need to have more shared outputs

sources as the CAN bus line is in some points interrupted according to bus tie breakers position.

Normally a collision would be indicated if there were more sources on the bus and this setpoint can be

used to disable the evaluation of collisions in this special case.

SHxOcol Detect

back to List of setpoints

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands