ComAp InteliDrive DCU Marine Manual Download

Page: 110 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

110

Engine commands and Statistics protection

Commands (Engine Cmd) password protection protects Start, Horn reset, Fault reset commands from

controller front panel buttons, remote displays, MODBUS line or InteliMonitor.

Selected Command password level 0, 1, 2, 3 is valid for all engine commands except of Stop. Stop command is

password protected separately by “Engine Stop” option.

Separately can be also protected statistic commands: ClearStatistics, SetSucc starts, EngRun hours,

SetUnsuc starts.

To set commands protection from DriveConfig:

1. Open DriveConfig

2. Select Commands window

3. Set Password = 0 (no protection) or level 1 or 2 or 3

Note:

Engine commands password protection works according to the description above from firmware version

ID DCU MARINE 2.1 and firmware versions of remote displays listed below. In older firmware versions “Engine

Cmd” group contains also Stop command, commands from ID-DCU MARINE local panel (buttons directly on

the controller) were not password protected in older versions.

InteliVision 5 CAN (Backlit) – from 1.3

InteliVision 8 (Marine) – depends on screen configuration in archive of ID-DCU MARINE controller. Default

archives for ID-DCU MARINE version 2.1 and higher support independent password protection of Stop

command according to description above.

Note:

All setpoints below can be modified from Remote panel or InteliMonitor as well.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands