ComAp IG-NT GC Reference Manual Download

Page: 196 / 260

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

196

Available in IS-NT only.

Binary input: PulseCounter 4

Related FW

3.0

Description

This is the input of the

PulseCounter #4

module. The module counts pulses at the

input and if the input pulses counter reaches value given by the setpoint

ConvCoefPulse4

, the counter value

PulseCounter 4

(in the group

Statistic

) is

increased by 1 and input pulses conter is reset to 0. Both counter value and input
pulses counter are stored in the nonvolatile memory.

The

PulseCounter

modules are intended e.g. for connecting external energy or

fuel meters with pulse outputs.

OTE

Minimal pulse width as well as minimal pause between two succesive pulses is
100ms.

OTE

The counter value can be reset in the InteliMonitor statistics window.

OTE

Available in IS-NT only.

Binary input: Timer block 1

Related FW

3.0

Description

This input is used to disable temporarily the output from the

Timer channel #1

OTE

Summary of Contents for IG-NT GC





































































































































































































































































Search results

Summary of Contents for IG-NT GC

Reviews:

Related manuals for IG-NT GC

Brands by name

Popular brands

ComAp IG-NT GC, Reference Manual

Search results

Summary of Contents for IG-NT GC

Reviews:

Related manuals for IG-NT GC

Brands by name

Popular brands