ComAp ID-FLX-Lite-PC Global Manual Download Page 88

Page: 88 / 211

InteliDrive Lite - 1.2.1 Global guide

Recommend USB cable: USB-LINK CABLE 1.8M - ComAp A-B USB cable.

8.4 IB-Lite (optional card)

Plug-in into InteliDrive Lite controller COMMUNICATION MODULE port.

10/100 MBit ethernet interface in RJ45 socket.

8.5 IL-NT GPRS (optional card)

Plug-in into InteliDrive IPC3 controller COMMUNICATION MODULE port.

GSM/GPRS modem

Quad Band

850/900/1800/1900MHz

GPRS multi-slot

class 10

CSD communication

up to 14.4kbps

TCP/IP communication

over GPRS

Voltage supply

8-36 VDC

8.6 IL-NT AOUT8 (optional card)

Plug-in into InteliDrive IPC controller EXTENSION MODULE port.

Number of PWM outputs

PWM frequency

1200Hz

Maximum current

0,5A

Maximum switching voltage

36VDC

Output resistance

1Ohm

Resolution

10bits

8.7 IL-NT AIO (optional card)

Plug-in into InteliDrive IPC controller EXTENSION MODULE port.

Resolution

10bits

Inputs

Number of Analog inputs

4 (2400Ohm, 20mA, 4V)

Maximal resistance range

2400Ohm

Maximal voltage range

Current range

0-20 mA

Input impedance (current)

180Ohm for mA measuring

Input impedance (voltage)

>68 kOhm for V measuring

Resistance measurement tolerance

±2% ±2 Ohm

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands