ComAp ID-FLX-Lite-PC Global Manual Download Page 74

Page: 74 / 211

InteliDrive Lite - 1.2.1 Global guide

Total Engine Hours

EngineHours

ANA

Boost Pressure

Boost Press

bar

ANA

Intake Manifold Temp

Intake Temp

°C

ANA

If Cummins-Modbus x.x option is selected, following values are read from Modbus Register Data (for QSX15,

QSK45, QSK60):

Value name

Short name

Dimension

Type

Frame name

Red Shutdown Lamp

Red Lamp

BIN

10005

Yellow Warning Lamp

Yellow Lamp

BIN

10006

Engine Speed

RPM

ANA

30001

Coolant Temp

°C

ANA

30002

Oil Pressure (psig)

Oil Press

bar

ANA

30003

Oil Pressure (psia)

Oil Press

bar

ANA

30003

Running Time

ANA

30008

Fuel Rate (UK)

Fuel

L/h

ANA

30018

Fuel Rate (US)

Fuel

L/h

ANA

30018

Intake Manifold Press

Intake Press

bar

ANA

30530

Intake Manifold Temp

Intake Temp

°C

ANA

30531

6.6 ECU Analog inputs

Reading of mentioned values from ECU enables to use analog inputs of the unit for other purposes, e.g.

measuring, displaying and alarm activation related to various quantities. The configuration thus allows using

nine analog inputs on the central unit and four analog inputs on plug-in module if connected.

If the engine without ECU is controlled by InteliDrive IPC, the first analog input is permanently configured to Oil

Pressure, other analog inputs remain freely configurable.

6.7 Tier4 final support

There was implemented support of Final Tier 4 (FT4) standard. Complete functionality is available only with

configured ECU what support FT4. It requires min.:

ECU List v6.3.0

LiteEdit v5.2.0.

FT4 support includes:

New screen Aftertreatment

The screen is visible only if configured ECU supports and transmits some FT4 messages. Actived FT4 icon

is indicated by alarm Aftertreatment. When any new icon appears, the controller automatically switches to

Aftertreatment screen.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands