manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 36

InteliDrive Lite - 1.2.1 Global guide

36

Note:

Boot jumper programming – In case of interrupted programming or other software failure is possible to

use the boot jumper programing to restore controller to working order. Connect the controller to PC, run LiteEdit

and wait until connection bar at bottom turns red. Then run programming process via menu Controller ->

Programming and cloning – Programming. Select correct firmware and confirm dialog. Then follow instructions

in LiteEdit.

Note:

Or follow video guide “Boot Jumper Programming“ at

www.comap-control.com

4.6.2 IL-NT RS233-485

IL-NT RS232-485 is optional plug-in card, which enables controller to RS232 and RS485 serial communication.

This is required for computer or Modbus connection. The IL-NT RS232-485 is a dual port module with RS232

and RS485 interfaces at independent COM channels. The RS232 is connected to COM1 and RS485 to COM2.

Adjustment of communication type, baud rate etc. is via Comms Setting group of setpoint in LiteEdit or the

controller screen.

4.6.3 IL-NT S-USB

IL-NT S-USB is optional plug-in card to enable communication of controller via USB port. This is required for

computer or Modbus connection. This module contains USB slave port, which is connected internally to the

COM1 of the controllers. It is designed as an easy removable service module.

This module requires a FTDI USB Serial converter driver installed in the PC. The driver creates a virtual serial

port (COM) in the PC, which must be used in LiteEdit as communication port when a connection is being

opened.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands