ComAp ID-FLX-Lite-PC Global Manual Download Page 33

Page: 33 / 211

InteliDrive Lite - 1.2.1 Global guide

4.5.3 IL-NT AIO

IL-NT AIO is optional plug-in card. This card offers additional four analog inputs and one analog output. Analog

inputs can be use for different types of sensor (resistive, current and voltage) and variable analog output, which

can be used as PWM. Adjustment of extension plug-in modul is possible via LiteEdit too.

Type of analog input is selectable by jumper. Each analog input has own line of jumper position. The top position

(closest to green conector on the pic above) is for resistive input, central position for voltage input and lowest

position is for current input.

AI1 - AI4

2600 Ohm / 4V / 20 mA

Iout

Uout

PWM

0 - 20 mA (max 22mA) max 100 Ohm load

0 - 4,5V (max 10mA)

PWM 5V / 15mA / 500 Hz

Not used

Do not connect!

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands