manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 204

InteliDrive Lite - 1.2.1 Global guide

204

10.2 Values

Values are displayed on the controller screen or are accessible via icon

in the LiteEdit PC tool.

See the table with all visible values in LiteEdit.

Note:

Some engine values (*) are visible only if the ECU unit is configured.

Groups

Name

Note

Load limit

LoadLimitOut

Engine values

RPM

RPM-BI3

ECU State (*)

ECU FreqSelect (*)

SpeedReq Abs

SpeedReq Rel (*)

Engine Speed

Fuel Rate (*)

CoolantTemp (*)

Intake Temp (*)

Oil Press (*)

Boost Press (*)

Oil Temp (*)

ECU-AIN 8 (*)

ECU-AIN 9 (*)

FuelUsed (*)

DPF1 Soot Load (*)

DPF1 Ash Load (*)

If ECU is not configured, then

is displayed only RPM, RPM-

BI3 and SpeedReq Abs

Statistic

Run hrs

Num starts

NextServTime

E-Stop

ShutDown

DayCons

TripCons

Day hrs

Analog CU

Ubat

D+

OilPressure

Engine Temp

Fuel level

Analog inputs are shown

depends on if they are

configured or not

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands