ComAp ID-FLX-Lite-PC Global Manual Download Page 196

Page: 196 / 211

InteliDrive Lite - 1.2.1 Global guide

196

Setpoint group

Sensor spec

Related FW

1.2.1

Range [units]

[-]

Default value

OFF

Force value

Step

[-]

Comm object

14283

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Setting of Counter 1 mode:

Always: Corresponding counter counts pulses all time.

Running: Corresponding counter counts pulses only when engine is running.

OFF: Corresponding counter does not count pulses. Default settings.

Note:

The Total 1 value is visible in LiteEdit – Values – Statistics. The Total 1 value disappears from

controller screen when Counter mode 1 is switched OFF otherwise there is new screen between existing

Statistics and Alarm list.

CounterMode 1

back to List of setpoints

10.1.17 Group: AIO module

Setpoint group

AIO module

Related FW

1.2.1

Range [units]

-100 - +10000 [V]

Default value

0 U8

Force value

Step

Comm object

13650

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The level for IL-NT-AIO plug-in card Analog input 1 alarm detection.

AnlInAIO1 lev1

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands