manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 191

InteliDrive Lite - 1.2.1 Global guide

191

Setpoint group

Sensor spec

Related FW

1.2.1

Range [units]

-1000 - +1000 [°C]

Default value

0 °C

Force value

Step

1 °C

Comm object

8407

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Calibrate the constant to adjust the measured value of InteliDrive IPC analog inputs. Physical dimension of

calibrating constant is corresponding to Analog input.

Note:

Calibration constants have to be adjusted when measured value is near the alarm level.

Calibr AI2

6

back to List of setpoints

Setpoint group

Sensor spec

Related FW

1.2.1

Range [units]

-1000 - +1000 [%]

Default value

0 %

Force value

Step

1 %

Comm object

8467

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Calibrate the constant to adjust the measured value of InteliDrive IPC analog inputs. Physical dimension of

calibrating constant is corresponding to Analog input.

Note:

Calibration constants have to be adjusted when measured value is near the alarm level.

Calibr AI3

6

back to List of setpoints

Setpoint group

Sensor spec

Related FW

1.2.1

Range [units]

-1000 - +1000 [U16]

Default value

0 U16

Force value

Step

1 U16

Comm object

11917

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Calibrate the constant to adjust the measured value of InteliDrive IPC analog inputs. Physical dimension of

calibrating constant is corresponding to Analog input.

Note:

Calibration constants have to be adjusted when measured value is near the alarm level.

Calibr AI4

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands