manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 190

InteliDrive Lite - 1.2.1 Global guide

190

Setpoint group

Date/Time

Related FW

1.2.1

Range [units]

1 - 1440 [min]

Default value

5 min

Force value

Step

1 min

Comm object

10201

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Adjusts duration of Timer 2 output.

Timer2Duration

6

back to List of setpoints

Setpoint group

Date/Time

Related FW

1.2.1

Range [units]

all dates

Default value

actual date

Force value

Step

one day

Comm object

10200

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Setting of the date when is activated Timer 2 with set Timer1 repeat = ONCEATDATE.

Timer2OnceDate

6

back to List of setpoints

10.1.16 Group: Sensor spec

Setpoint group

Sensor spec

Related FW

1.2.1

Range [units]

-1000 - +1000 [Bar]

Default value

0 Bar

Force value

Step

1 Bar

Comm object

8431

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Calibrate the constant to adjust the measured value of InteliDrive IPC analog inputs. Physical dimension of

calibrating constant is corresponding to Analog input.

Note:

Calibration constants have to be adjusted when measured value is near the alarm level.

Calibr AI1

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands