manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 188

InteliDrive Lite - 1.2.1 Global guide

188

Setpoint group

Date/Time

Related FW

1.2.1

Range [units]

all dates

Default value

actual date

Force value

Step

one day

Comm object

10043

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Setting of the date when is activated Timer 1 with set Timer1 repeat = ONCEATDATE.

Timer1OnceDate

6

back to List of setpoints

Setpoint group

Date/Time

Related FW

1.2.1

Range [units]

[-]

Default value

No Func

Force value

Step

[-]

Comm object

11661

Related applications

Config level

Standard

Setpoint visibility

Always

Description

No Func: Operates just corresponding LBO Timer2 according the Timer2 setting, see Timer2 repeat, Time2

ON time, Timer2Duration. Function operates in all OFF-MAN-AUT modes. Default state.

AutoRun: Engine automatically starts and stops in AUT mode (similar to LBI Rem start/stop, the same

record in the history) according the Timer2 setting.

AutoRegCMP: Start and stop engine in AUT mode according to the LBO Speed switch - see Regulator: Reg

CMP setpoints. The comparator function (output) works opposite when Regulator: Reg CMP On < Reg

CMP Off. The Date/Time: Timer2 repeat, Timer2 ON time, Timer2Duration settings are not important in this

case.

AutoBatt: Engine starts when actual Battery voltage < Engine protect: Batt und Batt volt del and

stays running for Date/Time: Timer2 Duration. Function operates in AUT mode.

AutoStop: Engine is switched from AUT to MAN and stopped or stopped from MAN mode (like by STOP

button) when engine runs longer then Date/Time: Timer2Duration on actual RPM less or equal Engine

params: Idle speed + 5% (fix limit). Function is not active during engine start.

Timer2Function

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands