manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 179

InteliDrive Lite - 1.2.1 Global guide

179

Setpoint group

Engine protect 2

Related FW

1.2.1

Range [units]

0 - 5 [RPM]

Default value

0 RPM

Force value

Step

0.1 RPM

Comm object

8708

Related applications

Config level

Standard

Setpoint visibility

Always

Description

There are two new protections related to RPM-BI3 where functions Engine protect: RPMdiff Sd, RPMdiff

Wrn limits depends on setting of GearBoxRatio:

Separate RPM-BI3 underspeed Wrn and Sd protection when Engine protect: GearBoxRatio = 0.0

Difference check between RPM and RPM3 with calculation of gear-box ratio, when Engine protect:

GearBoxRatio > 0.0. Protection is active when engine is Ready to load.

Note:

The RPM-BI3 measuring and corresponding protections are switched off when Basic setting:

GearTeethBI3 = 0. In this case BI3 operates as standard Binary input.

GearBoxRatio

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands