manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 156

InteliDrive Lite - 1.2.1 Global guide

156

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

[-]

Default value

DISABLED

Force value

Step

[-]

Comm object

14603

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The setting ENABLED disables all engine protections. They are just displayed on alarm list and recorded to

historry, but they have no influence to running engine. The setting ENABLED is indicated in tha alarm list as

warning

SdOverride Act

and recorded to history as record

SdOverride Act

.

Sd Override

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

[-]

Default value

ENABLED

Force value

Step

[-]

Comm object

14653

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The setting DISABLED disables all configured protections, except Overspeed and Emergency Stop. It is

indicated in the alarm list by warning Prot AIN1 dis. Each configuration change is recorded in history,

records: Prot AIN1 dis and Prot AIN1 ena.

Setpoint name depends on setting of AIN1 (maximum length is 14 characters).

AIN1 prot

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

-10 - +1000 [Bar]

Default value

2 Bar

Force value

Step

0.1 Bar

Comm object

8369

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Warning limit level for ANALOG INPUT 1

Setpoint name depends on setting of AIN1 (maximum length is 14 characters).

AIN1 Wrn

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands