manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 137

InteliDrive Lite - 1.2.1 Global guide

137

Setpoint group

Engine params 2

Related FW

1.2.1

Range [units]

[-]

Default value

DISABLED

Force value

Step

[-]

Comm object

9683

Related applications

Config level

Standard

Setpoint visibility

Always

Description

ENABLED: The D+ terminal is used for both functions - “running engine” detection and charge fail detection.

CHRGFAIL: The D+ terminal is used for charge fail detection only.

DISABLED: The D+ terminal is not used. Defult state.

Note:

The magnetization current is provided independently on this setpoint value.

Note:

The D+ charge fail protection becomes active after Engine params 2: Idle time reaches zero.

D+ function

6

back to List of setpoints

Setpoint group

Engine params 2

Related FW

1.2.1

Range [units]

[-]

Default value

DEFAULT

Force value

Step

[-]

Comm object

10266

Related applications

Config level

Standard

Setpoint visibility

Always

Description

This setpoint should be used only for Volvo and Scania engines.

Volvo – “Volvo Aux” is selected in ECU configuration:

Primary or secondary engine speed is set by Frequency select bits in VP Status frame.

Scania – “Scania S6 Singlespeed” is selected in ECU configuration:

Nominal engine speed is chosen by Nominal speed switch 1 and 2 from DLN1 frame when the engine is

running on nominal speed, i.e. binary output Idle/Nominal is active. When the output is not active (engine is

running on Idle speed), the setpoint ECU FreqSelect is not taken into account.

ECU FreqSelect

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands