manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 135

InteliDrive Lite - 1.2.1 Global guide

135

Setpoint group

Engine params 2

Related FW

1.2.1

Range [units]

0 - 3600 [s]

Default value

0 s

Force value

Step

1 s

Comm object

8662

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Run time of engine after cooling pump. Binary output Cooling pump is closed when the engine starts and

opens AfterCool time delayed after engine stops.

AfterCool time

6

back to List of setpoints

Setpoint group

Engine params 2

Related FW

1.2.1

Range [units]

[-]

Default value

DIESEL

Force value

Step

[-]

Comm object

9100

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Setpoint setting determines behavior of the Binary output FUEL SOLENOID.

DIESEL: Output closes 1 sec before Binary output STARTER.

The output opens if Emergency stop comes or Cooled engine is stopped and in pause between repeated

starts.

GAS: In this mode of operation the output closes to open the gas valve and enable the engine to start. The

delay of Fuel solenoid output activation in relation to Starter output is defined by FuelSol offset. The output

closes only if RPM > 30 (i.e. the starter motor is engaged).

The output opens if there is any reason to stop the engine or in pause between repeated starts.

Note:

In the case of gas engine, the underspeed protection cannot be blocked by the Sprinkler function.

Note:

For gas engines, it is strongly recommended to use the pick-up sensor, as non-zero RPM

detection is required during the start procedure.

Fuel solenoid

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands