manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 134

InteliDrive Lite - 1.2.1 Global guide

134

Setpoint group

Engine params 2

Related FW

1.2.1

Range [units]

5 - 1500 [RPM]

Default value

350 RPM

Force value

Step

1 RPM

Comm object

9095

Related applications

Config level

Standard

Setpoint visibility

Always

Description

“Firing” speed when InteliDrive IPC controller stops cranking (starter goes OFF).

Sd Underspeed protection is activated when RPM drops back below the Starting RPM for more than 5

second the engine starting procedure.

RPM meas fail indication

Can appears during "Cranking state" i.e. Starter (or J1939 Start command) is activated then one running

condition was detected (D+ was activated or (POil > Starting POil) condition was filled) - i.e. Starter was

switched off based on previous condition and within time (Cranking time and fix 5s) minimum RPM does not

appear (RPM > Starting RPM), then is activated RPM meas fail.

Note:

Limit is ignored when Gear teeth = 0 i.e. in engine operation without speed pickup (running state is

indicated from D+ or Starting POil.

Starting RPM

6

back to List of setpoints

Setpoint group

Engine params 2

Related FW

1.2.1

Range [units]

0 - 10 [Bar]

Default value

10Bar

Force value

Step

0.1 Bar

Comm object

9681

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Controller stops cranking (starter goes OFF) when Oil Pressure (typically measured on AIN1) is over

Starting POil.

Note:

Oil Pressure can be also measured on binary sensor. Then is necessary adjust AIN1 as Binary

input and Starting POil=1.

Note:

There are three conditions for stop cranking: Starting RPM (just in case the Gear teeth > 0),

StartingPOil and D+ (if enabled). Starter goes off when any of these conditions is valid.

Starting POil

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands