manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 126

InteliDrive Lite - 1.2.1 Global guide

126

Setpoint group

Comms settings

Related FW

1.2.1

Range [units]

[-]

Default value

ENABLED

Force value

Step

[-]

Comm object

24365

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The option allows or blocks the function of AirGate. For AirGate function is necessary to use communication

plug-in modules IB-Lite or IL-NT-GPRS or InteliDrive Lite partly supports IB-NT too.

DISABLED: Blocks the function of AIrGate.

ENABLED: Allows function of AirGate. Default state.

AirGate

6

back to List of setpoints

Setpoint group

Comms settings

Related FW

1.2.1

Range [units]

[-]

Default value

airgate.comap.cz

Force value

Step

[-]

Comm object

24364

Related applications

Config level

Standard

Setpoint visibility

Always

Description

AirGate Address. The default address is „airgate.comap.cz“.

Note:

To reduce the data traffic over cellulat network you can set in setpoint group „Comms Settings“ 

the parameter „AirGate IP“ = 80.95.108.26. This will save significant data amount needed for translation

of Airgate server IP address. In case of changing the server IP address this settings has to be updated or

returned to default „airgate.comap.cz“.

IMPORTANT: All manipulations with IL-NT-GPRS module has to be done with DC power

supply switched off. Module can be only powered while is plugged into the controller and

together with controller!

AirGate IP

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands