ComAp ID-FLX-Lite-PC Global Manual Download

Page: 121 / 211

InteliDrive Lite - 1.2.1 Global guide

121

10.1.6 Group: Comms settings

Note:

Following setpoints are available from Controller and LiteEdit/InteliMonitor.

Setpoint group

Comms settings

Related FW

1.2.1

Range [units]

1 - 32 [-]

Default value

Force value

Step

[-]

Comm object

24537

Related applications

Config level

Standard

Setpoint visibility

Always

Description

It is controller’s identification number. It is possible to set controller address different from the default value 1

so that more InteliDrive IPC controllers can be interconnected (via RS485) and accessed e.g. from Modbus

terminal.

Note:

When opening connection to the controller its address has to correspond with the setting in PC

tool.

ControllerAddr

back to List of setpoints

Setpoint group

Comms settings

Related FW

1.2.1

Range [units]

[-]

Default value

DIRECT

Force value

Step

[-]

Comm object

24522

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Communication protocol switches for the COM1 channel.

DIRECT: LiteEdit communication protocol via direct cable or AirGate, WebSupervisor communication

protocol via AirGate.

MODEM: LiteEdit communication protocol via modem.

MODBUS: Modbus protocol. See detailed description in InteliDrive Communication Guide.

ECU LINK: Protocol for communication with Cummins engines via Modbus.

Note:

For details on communication speed and other technical parameters please see chapter Technical

Data.

Note:

For detailed description see chapter Modbus protocol.

COM1 Mode

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Related manuals for ID-FLX-Lite-PC

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Related manuals for ID-FLX-Lite-PC

Brands by name

Popular brands